Welcome to OStack Knowledge Sharing Community for programmer and developer-Open, Learning and Share
Welcome To Ask or Share your Answers For Others

Categories

0 votes
1.1k views
in Technique[技术] by (71.8m points)

arm - STM32F207 bare metal SPI RXNE and TXE not working?

I need to communicate with an eeprom chip(25lc1024) via SPI. I can get the following code to work but have to resort to delays isntead of the flags alone. Otherwise I can see on the scope that it is not waiting for all the bits to be shifted out and proceeds. Any ideas why the flags are not stopping it?

void  Init_SPI(void){
    RCC->APB2ENR |= RCC_APB2ENR_SPI1EN;   // enable SPI clock

    GPIOA->AFR[0] |= SET_AFL_A_FOR_SPI1;
    GPIOB->AFR[0] |= SET_AFL_B_FOR_SPI1;

    SPI1_NSS = DESELECT_CHIP;            // set the SS pin high
    
    // initialize the SPI configuration register
    SPI1->CR1  =  SPI_CR1_MSTR  // SPI master mode
                | SPI_CR1_BR_1; // 010 bit rate prescale /8 (60MHz/8 = 7.5MHz)
    SPI1->CR2  =    SPI_CR2_SSOE;
    
    SPI1->CR1  |= SPI_CR1_SPE;  // enable SPI
}

unsigned int eeprom_read(unsigned long address, unsigned int chars_to_read)
{
    char temp;
    unsigned int result = 0;


    SPI1_NSS = SELECT_CHIP;                         // set the SS pin low
    SPI1->DR = READ_FROM_SPI;                       // send data out SPI
    while( !(SPI1->SR & SPI_SR_TXE) );              // wait until transmit buffer empty

    SPI1->DR = (address & 0xFF0000) >> ADJ16;   // send data out SPI
    while( !(SPI1->SR & SPI_SR_TXE) );              // wait until transmit buffer empty
    SPI1->DR = (address & 0x00FF00) >> ADJ8;    // send data out SPI
    while( !(SPI1->SR & SPI_SR_TXE) );              // wait until transmit buffer empty
    SPI1->DR = (address & 0x0000FF);                    // send data out SPI
    while( !(SPI1->SR & SPI_SR_TXE) );              // wait until transmit buffer empty

    delay();
    temp = SPI1->DR;
    SPI1->DR = DUMMY_8BIT;                    // send dummy 8 bits to generate clock
    chars_to_read--;

    while( !(SPI1->SR & SPI_SR_RXNE) );             // wait until receive buffer is not empty
    
    //USART2->DR = SPI1->DR;
    result = SPI1->DR;
    
    if(chars_to_read != 0){
        while((SPI1->SR & SPI_SR_RXNE) );               // wait until receive buffer is empty
        delay();
        SPI1->DR = DUMMY_8BIT;                    // send dummy 8 bits to generate clock
        
        //delay();
        while( !(SPI1->SR & SPI_SR_TXE) );              // wait until transmit buffer is empty
        while( !(SPI1->SR & SPI_SR_RXNE) );             // wait until receive buffer is not empty
        temp = SPI1->DR;
        result = (result*256) + temp;
        chars_to_read--;
    }
    
    delay();
    SPI1_NSS = DESELECT_CHIP;                                   // set the SS pin high
    
    return result;
}

static void delay(void)
{
    unsigned int j = FALSE;
    for (j = 0; j < 25; j++) {
    }
}

question from:https://stackoverflow.com/questions/66060101/stm32f207-bare-metal-spi-rxne-and-txe-not-working

与恶龙缠斗过久,自身亦成为恶龙;凝视深渊过久,深渊将回以凝视…
Welcome To Ask or Share your Answers For Others

1 Answer

0 votes
by (71.8m points)
Waitting for answers

与恶龙缠斗过久,自身亦成为恶龙;凝视深渊过久,深渊将回以凝视…
Welcome to OStack Knowledge Sharing Community for programmer and developer-Open, Learning and Share
Click Here to Ask a Question

...